Product search:
Product List
>> Besturn X80 series
>> Besturn B90 series
>> Besturn B70 13 paragraph 1.8F Series
>> Besturn B70 10 Series models
>> Besturn B70 series
>> Besturn B50F series
>> Besturn B50 series
>> FAW Oulang Series Field
>> Jinan Heavy Truck N70 Series
>> Red Audi Series
>> Hongqi Century Star Series
>> Bora, Audi A6 series
>> Mazda M6, M3, M2 Series
>> Modern series
>> Mercedes-Benz Series
>> Chery series
>> Other series
>> Big Truck Series
 
  News
Mold design and manufacturing considerations
2013-09-11 14:54:07

A . Glue bit check
Check the adhesive level is uniform, as it will cause uneven shrinkage and affect appearance.

Two . OK parting with draft angles
1 Select the parting surface projected on the mold opening direction maximum possible simplification


(2) wear a bit touch : touch as much as possible after the mold , such as to touch the former model , easy going burr , affecting the appearance , the use of surface contact.


3 pillow bits: pillow 5-8 mm , and then type surface is flush with the Oita , glue bit partial pull 3 degrees , 3 degrees or pull back to avoid empty .


4 inserted through the bit : the use of side work , pulling three degrees , generally do inserts .

III. Draft Principles
1: Less glue directions draft.


2: The maximum shaft end for the product size , pore size for the product category smallest side .

Four . 2D Mirror
2D must pay attention to the mirror and put the shrink, if I forget this step , most of the mold scrapped .

Five . Shrink
Shrinkage small products (5 ‰ less ) may experience put shrink , shrinkage great products, such as a can also be put up 18 ‰ 20 ‰ 22 ‰ can be put even more products , be sure to seek the views of responsible person alive again , avoid dimensions do not coincide with complementary products .

VI. Sprue should coaxial eccentric KO
Seven . Line position points
A general use Bevel Pillar for power, a relatively small core pulling away with a T-shaped slot , with more than 30mm core pulling cylinder .


(2) the angle of bevel pillar angle smaller than shovels 2-3 degrees .


3 After the mold line position into the front mold half more than the total height can dispense with shovels , to make use of the former mold machining surface pressure surface .


4 OK bit wider than 100mm, try to use two inclined guide post, more than 150mm in the middle of the guide groove .


5 line-bit positioning: do not try to Boyjazz Pinball ( force is not big enough ) , with a screw positioning .


6 lines located at TOP , be sure to put a spring , or the finish line bit mode due to gravity , not a result of homing crashed .


7 mold opening direction of the projection, such as line position beneath a slant or a thimble , to set the first reset mechanism , or they may line position with the lifter or thimble will produce interference .


8 -bit line with walking , walking beer handles, plastic bag in straight body out .


9 line digital journey should be greater than buckle Bits 2 to 3mm, cylinder stroke buckle bit should be greater than 10mm.


10 In order to increase the firmness of shoveling machine , try to do a backhoe .

Eight . Slant design elements
1 slant generally do 3-8 °, of not more than 15 °.


2 Ejector stroke is generally greater than buckle -bit 0.5-1mm.


3 Ejection Direction : plastic bit should be flat or up , or do delay the lifter .


Slant width comparison hours, ejector plate to increase a frame, so that the lifter height shortened to ensure strength .

 

Address:Changzhou Xiaohe Industrial Zone, Fu Ping Road 26 Phone:0519-88617251 0519-88617252
Changzhou tiannuo molding co., LTDAll Rights Reserved